Morse Keyboard

Coming soon to the App Store

Morse code phrase

Goodbye in Morse code

Updated November 21, 2026 · By the Morse Keyboard team at Yarsa Labs

The answer

“Goodbye” in Morse code is --. --- --- -.. -... -.-- .. It is one word, so there is no slash, just seven letters with a gap after each. On the air, a full goodbye is rare. Operators close a contact with a handful of short signs, and the very last one has its own place in the ITU standard.

One word, seven letters.

Letter by letter

LetterMorseMarks
G--.Dash Dash Dot
O---Dash Dash Dash
O---Dash Dash Dash
D-..Dash Dot Dot
B-...Dash Dot Dot Dot
Y-.--Dash Dot Dash Dash
E.Dot

Heavy start, light finish

The front of the word is weighty. GOOD is twelve marks, and only three of them are Dots. The double O in the middle is six Dashes in two even groups, a long, slow stretch that is easy to hear and hard to rush.

Then BYE lightens it. B is a Dash and three Dots, Y swings back to Dash Dot Dash Dash, and E ends on a single Dot. The word sounds like it slows down, then trails off, which suits it.

At 79 units it is a long single word. BYE alone is -... -.-- ., 29 units, a little over a third of the full word.

Length and timing

“Goodbye” is 1 word, 7 letters and 21 marks: 8 Dots and 13 Dashes. With standard timing it is 79 units long, from the first mark to the last: a Dot is 1 unit, a Dash 3, the gap inside a letter 1, between letters 3 and between words 7.

SpeedOne unitThe whole phrase
5 WPM240 ms19.0 seconds
13 WPM92.3 ms7.3 seconds
20 WPM60 ms4.7 seconds

Speed is counted in words per minute (WPM), using the word PARIS. Morse code speed and Farnsworth timing

How a contact ends

A Morse contact between two radio operators tends to close in stages. In plain words, a typical ending goes like this: one operator thanks the other for the contact, sends their regards, says something like "hope to hear you again", and gives their own call sign. The other replies in kind. Then one of them sends the end-of-work signal, and the contact is over.

Each of those steps has a short form, because nobody wants to send GOODBYE letter by letter at the end of a long chat:

  • GB means goodbye: --. -...
  • CUL means "see you later": -.-. ..- .-..
  • 73 means "best regards": --... ...--. See 73 in Morse code.
  • TU means thank you: - ..-

The final sign is SK, ...-.-. In ITU-R M.1677-1 it is called the "end of work" signal, and the standard says the station that sent the last message should send it. Maritime abbreviations write the same signal as VA. Amateur operators call it SK and often say it means "end of contact".

Short forms and signs

SignMeaningNote
GBGoodbyeInformal radio shorthand
CULSee you laterInformal radio shorthand
73Best regardsNumbers, sent as figures
SKEnd of workOne sign, no gap between S and K
BYEByeThe plain word, shorter than GOODBYE

SK has a second meaning among amateurs: "silent key", a phrase for an operator who has died. Context makes the difference. At the end of a contact, it means the contact is done.

Ways to send it

  • End a message the way operators do. Instead of GOODBYE, sign off with TU 73 SK, which is thank you, regards, done: - ..- / --... ...-- / ...-.-.
  • A last tap at the door. BYE is short enough to tap on someone's hand as they leave.
  • A farewell card. Spell GOODBYE across the front and put GB on the back, so the card holds both the long and the short form.
  • Flash it at the end of a visit. The heavy Dash section at the start is easy to see from a car or a window.

Send “Goodbye” as sound, light or vibration with Transmit in Morse Keyboard.

Coming soon to the App Store

Easy ways to get it wrong

  • Sending SK as two letters. S, a gap, then K reads as the letters SK. The signal is one pattern, ...-.-, with no letter gap inside it.
  • Writing "73s". 73 already means regards, so many operators see the added s as redundant. Send 73 on its own.
  • Losing the Dot in G. G is --.. Drop its Dot and you have M (--), so GOOD reads MOOD. Next to two Os made only of Dashes, that last Dot is easy to swallow.
  • Mixing up B and D. B is -... and D is -... One Dot too few and GOODBYE becomes GOODDYE.

Learn the letters, then tap it by heart.

A keyboard laid out as the Morse code tree, with a course of a weekend and four weeks. Day 1 is free.

Coming soon to the App StoreSee how it works